Видео

if you havew this new engine it have low oil sensor which shuts engine down

Will this work with 2 electric pressure washers? For example 2 1.2 gpm 1800psi Ryobi Ressure washers x 2 = 2.4 gpm 3600psi?

Hi I have a question about one of your products.

Super video!

Of course the parts list link doesnt work

Just used this gun for the first job. Spraying woodluxe on a fence for four days. Lots of stip and go short trigger pulls. Gun ran smooth for the first day. Then the trigger started sticking. You pull it and then it stays depressed an extra second or two after you release pressure. Not a huge deal on this fence but could be catastrophic if your gun doesnt stop spraying when you tell it to. Unlike the rx pro, you better keep a bottle of pil or wd40 close by to wet the hinge and needle every so often.

What are the applications for each?

Bonjour comment démonter celle d un moteur honda gx340 11

I thought the clearing her throat was distracting and then 8:12 SUPER DISTRACTING! LETS FOCUS HERE YOUNG LADY I mean, how did she AVOID chiming in at 9:23 or 9:33?? 9:45 THAT IS HOW YOU MAKE A DOUBLE ENTENDRE VIDEO LOL

Jo

Your videos have helped me throughout my 5 yrs in the industry! And YES! I completely missed the set screw! Daaaamn it

What psi you think a 20hp engine would produce with that pump?

I was thinking of the same thing on my cordless pressure washers since I have 4 of the same kind but they are all brushed motors 😅

Is this brand better than the Lander ?

So, I have to assume that the set screw isn't going to be used on this particular pump?

I need some advice, looked at 4400PSI Westinghouse, Simpson, and Dewalt pressure washers. They are IDENTICAL. Who makes them? I discovered this after buying the Westinghouse and Simpson. Both had the same issue. The airbox was broken where it connects on top of the carb. The units incredibly difficult to start and they run like ABSOLUTE SHIT. At full throttle, I need to have the wand depressed or the engine stalls, or violently jack hammers around. I cannot safely operating it anywhere without strapping it to the ground with hard stakes. On pavement, I have to use my truck wheel chocks. I've used many small engines in the past, their engines do not seem balanced and I am sure they will explode if continue running them. Both have been returned. WTH????????

I have a Simpson that ran great when I got it last fall. This spring it didn't want to spray right, and I pumped the trigger a few times, and it started working just as I was ready to give up. The very next day it didn't want to spray again, and it started to spray like the day before and just then the engine died, and I have not been able to get it to run since. Knowing spark, fuel, air I checked all these things, three times over. Still have no idea what the problem is. For as much as this thing cost I would expect better than this.

Thanks that help alot

Which pressure washer is this?

How to order??

Good video. I must be in the 5%. My new GX390 pulls easily as if there is no compression stroke. It ran well for the first ten minutes hesitated couple of times within about 10 seconds of each other. Then it died and wouldn't start. Someone suggested to disconnect the yellow oil sensor wire. That didn't work.

Thank you so much for the information

Quick question Isn’t there a gasket/o ring type piece inside the housing of the pump (near the shaft hole?) I think I might have lost/misplaced mine..

Loosening that vault screw was crazy. I had my surface cleaner in a leg lock, leaned back, and used my full body weight to get is loose 😂 Thanks for the video.

Thank you so much boy did I feel silly when I realized why the keeper would go through 😂

I don’t have a set screw and my pump is just stuck on. I’ve looked very carefully for about an hour and no screw. What could it be

i like the pump.but not the inlet and out let for the water. cause just clips o the fitting but it leaks when there is pressur on the line

Bonjour 👋 je suis intéressé par cette pump

That was a big help thank you

how much is this specific unit?

Great thanks

I just replaced a pump going from a worn out 4k 3.5 to a new commit 4k 4gpm and it seems like the pressure especially when using my service cleaner got worse. Was I suppose to prime the pump some how or something? Or should I turn the unloader all the way?

can i use 5/8 hose with this pump?

Will the valve plug o-rings from this kit fit the 3DNX25GSI?

Are you still selling these

These are trash. Didn’t even make it through the first job!

how much is the manifold

What size is the hose for the top of the proportioner connecting to the 12v? I have 5.5 gpm everflo for batch mixing, but I have a 1 inch clear hose pulling from the tank. I’d like to order this proportioner. Link?

Honda was number one once, long ago 😢😢😢

where did you get your parts from?

Is there one that is 115v that I can plug straight to my house outlet instead of 12v battery?

Hie how can l acess or where can l buy pressure pump plz assist

Still won’t start , I tried every method you did

Did all this and still NO pressure. 🤷‍♂️

Use a ratchet to take out carb cap plug. Wrench can easily strip that bolt.

Easy kleen is much better.

Great advice. Thanks for sharing

What anti-seize do you recommend? Specific?

Some one replaced mine has a gap between the pump and engine cus they put spacers is that ok

👍